Could someone help me out and save me some time by explaining how to receive the temperature and humidity off of the SHT10 Humidity Sensor?
This is best described in the SHT10 Datasheet
- there are specific timings required to initiate
an incorrect timing will be ignored communication
- what and which commands are valid
- the format of the incoming results
- accuracy +/- and calibration, ranges, formulas
- humidity is dependant on current temp.
As well as sensor considerations to keep it working
But, ahh, is this not very much less than Nextion related?
Yes, this isn't related to Nextion but I don't know where else I could've gotten your detailed replies :)
I'll promise not to write any more irrelevant posts if you could please give me a link to where I can find this datasheet. I've looked around and ITEAD studios has nothing on the subject...
I've purchased two of them and I didn't have any other choice :)
By the way, I'm awaiting my Salae Logic Analyzer any day now so hopefully we'll resume our discussion about those 0xFF bytes.
Intel decided to bring Edison to End of Life
- I haven't seen them go on any kind clearance sale yet.
Be on the look out for good prices,
but try not to bid against each other (to keep final bids low)
Datasheets sources include places such as
sparkfun.com and adafruit.com
- sparkfun has many tutorials and additional info
- adafruit also has many tutorials and libraries
Distributors such as digikey
- a datasheet or link to datasheet for almost every part carried
Manufacturers or the who holds the design (sensirion for SHTs)
Google partno datasheet (or Bing Yahoo)
- avoid more the ad traps that make download some maze to get
- but when you see digikey, sparkfun, adafruit in the results
- pretty sure bet they will have if they sell or once sold it
Thanks a lot for the links!
Concerning Edison, you're right: it was discontinued a week or so ago. But, there still remains the Quark D2000. Any thoughts on it?
PS: I've just received two new Capacitive 7'' Nextion displays, both of them repeat the strange 0xFF behavior when working with Edison... I'll carry on looking into the issue once I get the analyzer.
Regarding Edison, my opinion goes something like
if it was a serious development towards a product,
PCB changes to consolidate external sensors.
then Intel resources to help with development still exist
the SoC either remains available or offer similar chips
- Edison was a mainstream mobile chip with graphics fused out
Any serious developments will still move foreward
as they did before the Edison
But what they failed to capture was the linux developers
When I program a executable on a 32-bit Linux server
- that executable was portable to the Edison, just upload.
From an internet enabled standpoint
- all the normal server apps, raw TCP/UDP was possible
But this is kind of lost/glossed over to those not familiar.
Quark is a Pentium chip complete with floating point bug.
shrunk down to 22nm running at 100MHz
But here they have a used a different operating system
so less chances of a rapid development
Edison has a Quark onboard
When they reduced ram/storage to sub megabyte,
there goes any thoughts of retro/nostalgia
and development with older tools also out the door.
Curie again too small for retro, I believe was a shrunken 486
unfamiliar OS, new learning curve, less hackers
Joule, damn. it was a Steroid Junkie as an MCU resources galore
So I think they lost much of their opportunity with the old school
that could have been what they needed to keep development going
But the rest of their normal development continues as it did
I'll probably look for Edisons to go on sale, modules and mini-breakouts
I somehow always felt the oversized Arduino board defeated their
whole accomplishment of miniaturizing the chip so small
Not that 5V compatibility wasn't a good idea over 1.8V logic
But I was drawn to where a "server" could be put into tight spaces
Just read a bit more on the D2000
- Pentium but without Floating Point Unit
- 32MHz clock
- 8K Sram + 32K Flash
It's now been so watered down ... not for me.
I agree, Intel seems to have lost its ideologists. This is somewhat similar to what happened at IBM a while ago.
I still hope that they will offer some substitute to Edison.
Joule is a marvel, I've got a 570x, but it isn't cost-efficient and also needs to be cooled with a fan, which is not always something you can provide.
If you do find some worthy alternative to Edison, I'll be thankful if you would let me know.
Also, I've started a new thread to continue the discussion on the multiple 0xFF transmission issue.